NITRONIC® 60 (Alloy 218) (UNS S21800)
NITRONIC 60 Datasheet
Cr 17, Mn 8, Ni 8.5, Si 4, N 0.13, C 0.10, Fe Bal.
High Performance Alloys stocks and produces this grade in the following forms: Bar, flat bar, square bar, wire spool. wire cuts, loose coil, sheet, plate, strip, coil, tube, pipe, fastener, disk, machined, billet, ingot. Request quote on this grade.
- Download Brochure 4 MB PDF - Or view as HTML
- Download FDA statement concerning the use of stainless steels as food contact surfaces of equipment. 154 KB PDF
Austenitic Stainless
NITRONIC 60 properties
| Wear Compatibility of NITRONIC 60 wear compared to Cobalt 6B and
17-4PH Against Various Alloys |
||||
| Alloy | Hardness | 17-4 PH
(HRC 43) |
NIT 60
(HRB 95) |
Cobalt 6B
(HRC 48) |
| 304 | HRB 99 | 24.7 | 6 | 3.1 |
| 316 | HRB 91 | 18.5 | 4.3 | 5.5 |
| 17-4 PH | HRC 31.5 | 66.1 | 4.9 | 2.7 |
| 17-4 PH | HRC 43 | 52.8 | 5.4 | 3.8 |
| NIT 32 | HRB 95 | 17.2 | 3.2 | 2 |
| NIT 50 | HRB 99 | 15.7 | 3.5 | 2.9 |
| NIT 60 | HRB 95 | 5.4 | 2.8 | 1.9 |
| Cobalt 6B | HRC 48 | 3.8 | 1.9 | 1 |
| Chrome Plate | --- | 3.3 | 2.1 | 0.3 |
| Silicon Bronze | HRB 93 | 2 | 2.2 | 1.9 |
| K-500 Monel | HRC 34 | 34.1 | 22.9 | 18.8 |
| 416 | HRC 24 | --- | 5.5 | 43 |
| 431 | HRC 32 | --- | 3 | 1 |
| Waspaloy | HRC 36 | --- | 3.1 | 2.4 |
| IN 718 | HRC 38 | --- | 3.1 | 2.7 |
| IN X-750 | HRC 36 | --- | 5.5 | 8 |
| Weight Loss of Couple (mg/1000 cycles) | ||||
This wear data republished from Armco brochure.
- Automotive valves - can withstand gas temperatures of upto 1500°F for a minimum of 50,000 miles.
- Fastener galling - capable of frequent assembly and disassembly, allowing more use of the fastener before the threads are torn up, also helps to eliminate corroded or frozen fasteners.
- Pins - Used in roller prosthetics & chains to ensure a better fit of parts (closer tolerance, non-lubricated) and longer lasting.
- Marine shafts - better corrosion than types 304 and 316, with double the yield strength.
- Pin and hanger expansion joints for bridges - better corrosion, galling-resistance, low temperature toughness, & high charpy values at sub-zero temps compared to the A36 and A588 carbon steels commonly used.
Material in this bulletin has been reprinted from Armco Bulletin No S-45, other Armco sources, and HPAlloys data.
NITRONIC ® is a registered trademark of AK Steel.
Page Contents: